New website

We are still working on improvements. To buy standards or add to a subscription, you must log on to the old website (the one you are on now) with your old username and password.


ISO 21003-1:2008

NOK 1 245,00 (excl. VAT) InformationMonitor standard
basket Webprint basket Printed and bound
Get online access
Status: Check Published
Norwegian title: Multilayer piping systems for hot and cold water installations inside buildings — Part 1: General
English title: Multilayer piping systems for hot and cold water installations inside buildings — Part 1: General
Item type: Standard
Language: Engelsk
Edition: 1 (2008-06-30)
Number of pages: 10

NOK 1 245,00 (excl. VAT)
NOK 1 556,25 (with VAT)

Scope: <p>This part of <std><std-ref>ISO 21003</std-ref></std> specifies the general aspects of multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water — whether or not the water is intended for human consumption (domestic systems) or heating systems — under specified design pressures and temperatures appropriate to the class of application (see <xref ref-type="table" rid="tab_1">Table 1</xref>).</p><p><std><std-ref>ISO 21003</std-ref></std> is a reference product standard (see <xref ref-type="sec" rid="sec_3.4.3">3.4.3</xref>). It is applicable to multilayer pipes, fittings, their joints, and also to joints with components made of other plastics and non-plastics materials intended to be used for hot and cold water installations. This part of <std><std-ref>ISO 21003</std-ref></std> is intended for use only in conjunction with all the other parts of <std><std-ref>ISO 21003</std-ref></std>.</p><p><std><std-ref>ISO 21003</std-ref></std> applies only to multilayer pipes with their inner layer made of plastics.</p><p>It covers a range of service conditions (application classes) and design pressures. It is not applicable for values of design temperature, <italic><styled-content style="font-family:Times New Roman">T</styled-content></italic><sub>D</sub>, maximum design temperature, <italic><styled-content style="font-family:Times New Roman">T</styled-content></italic><sub>max</sub>, and malfunction temperature, <italic><styled-content style="font-family:Times New Roman">T</styled-content></italic><sub>mal</sub>, in excess of those in <xref ref-type="table" rid="tab_1">Table 1</xref>.</p><non-normative-note><label>NOTE 1</label><p>It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.</p></non-normative-note><p>The polymeric materials used for the stress-designed layers are the following: polybutylene (PB), polyethylene of raised temperature resistance (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP) and chlorinated poly(vinyl chloride) (PVC-C).</p><p>The PE-X used shall be fully crosslinked and shall comply with the requirements of the relevant reference product standard (<std><std-ref>ISO 15875</std-ref></std>).</p><non-normative-note><label>NOTE 2</label><p>For the purposes of <std><std-ref>ISO 21003</std-ref></std>, crosslinked polyethylene (PE-X) as well as adhesives are considered as thermoplastic materials.</p></non-normative-note><p>Solid-wall pipes with thin outer layers (applied as protection layers or barrier layers, for instance) are not covered by <std><std-ref>ISO 21003</std-ref></std> but are specified in the Amendments to <std std-id="iso:std:iso:15874:-2:en" type="undated"><std-ref>ISO 15874-2</std-ref></std>, <std std-id="iso:std:iso:15875:-2:en" type="undated"><std-ref>ISO 15875-2</std-ref></std> and <std std-id="iso:std:iso:15876:-2:en" type="undated"><std-ref>ISO 15876-2</std-ref></std>. The total thickness of such outer layers, including the thickness of the adhesives used, shall be ≤ 0,4 mm.</p>
Adopted: 2008-06-30
ICS: 91.140.60 - Vannforsyningssystemer
23.040.01 - Rørdeler og rørledninger generelt